Current Students (20):
Alan Do, “Mechanical Testing of 3D Printed Multi-Material Structures, September 2024 – Present
Brooklynn Petty, “Towards In-Line Confocal Microscopy for Thickness Measurement of Roll-to-Roll Polymer Web”, January 2024 – Present
Akash Jape, “Development of a Digital Micromirror Device Graphical Interface for Customized Spatiotemporal Intensity Modulation in Microscale Selective Laser Sintering”, July 2024-Present
Alexandra Woods, “Design and Fabrication of a Furnace for Powder Emissivity Measurements,” January 2024 – Present
Brian Lee, “Towards In-Line Confocal Microscopy for Thickness Measurement of Roll-to-Roll Polymer Web” – May 2024 – Present
Daria Holoman, “Electrical Performance Characterization of Titanium Dioxide Nanomaterial Arrays for Triboelectric Nanogenerators,” June 2024 – Present.
Erick Ivan Lara, “Electromagnatic Damping of a Flexure-based Nanopositioning System”, June 2024 - Present
Kendra Hernandez, “Straining PID Crystals”, January 2024 – Present
Nikitha Garlapati, “Testing the Diffusion Properties of Polymerization Induced Phase Separation Structures,” September 2023 - Present
Prince Fofanah, “3D printing TPMS Polymerization Induced Phase Separation Structures, September 2023 - Present
Makayla Makuvise, “Testing the Diffusion Properties of Polymerization Induced Phase Separation Membranes,” September 2023 - Present
Nikhil Pai, “Thermal Camera Metrology of Nanoparticle Bed Heating in Microscale Selective Laser Sintering” September 2024-Present
Jacob Norris, “Dry Graphene Transfer”, June 2023 - Present
Jacob Haider Khan, “Design of Chiplet Assembly Systems”, September 2023 - Present
Andres Rodriguez, “Design and Fabrication of a Wire Drawing System”, May 2023 - Present
Orlan Oconar, “Modeling of Fluid Flow through TPMS Heat Exchangers”, May 2023 - Present
Sofia Frey, “Setup of a MEMS-based AFM”, January 2023 - Present
Alessandra Grady, “Nanomaterials Testing using AFM”, May 2023 - Present
Nathan Shu, “Selective Laser Sintering Power and Resistivity,” May 2023 – Present
Quentin Cole Schuelcke, “Motor Control in Roll-to-Roll Manufacturing”, September 2022 - Present
Former Undergraduate Students (82):
82. Adhvayith Sriram, “Mechanical Testing of LPBF Parts with Embedded Sensors”, January 2024 – August 2024
81. Kushaal Singh, “Photoelastic Imaging of Nanopatterned Thin Film” September 2023 – December 2023
80. Connor Chua, “Photoelastic Imaging of Nanopatterned Thin Film” September 2023 – December 2023
79. Ishan Chhatbar, “Micro-SLS Coating Setup”, January 2023-May 2023
78. Noor Khourdy, “A Microfluidic System for Emulsion Polymerization”, May 2023 – December 2023
77. Tyler Watts, “Design of a Flexure Based Nanopositioning System”, September 2022 – May 2023
76. William Li, “Micro-SLS Coating System Design”, September 2022-May 2023
75. Elisante Msenge, “Image Segmentation Analysis” – September 2022 – December 2022
74. Anoushka Sharma, “Image Segmentation Analysis” – September 2022 – December 2022
73. Jose Saucedo, “Image Segmentation Analysis” – September 2022 – December 2022
72. Samik Singh, “Image Segmentation Analysis” – September 2022 – December 2022
71. Catherine Lacey - "Optimization of Circuitry and Dry Electrode Arrangement for a Biostimulation Device with EMG monitoring", Undergraduate Research Student, June 2022- August 2022
70. Ang Gao, “PDI crystal growth”, September 2022- December 2023
69. Makenna Hayes, “Nanomaterials for Wearable-based Integrated Biostimulation” September 2020-May 2022
68. Daniel Moran, “Nanomaterials for Wearable-based Integrated Biostimulation” September 2021-May 2022
67. Daniel Nguyen, “Non-reciprocal Acoustic MEMs Metamaterials with Spatiotemporal Stiffness Modulation”, September 2021 – May 2022
66. Steven Kroleski, “Multi-layer Slot Die Coating Simulations”, May 2021-December 2021
64. Steven Padua, “3D Printed Biodegradable Implants for Single-Inoculation of Multiple-Dose Vaccines”, January 2021 – December 2021
63. Bolun Zhang, “Testing of Mechanical Metamaterials”, January 2022 – May 2022
62. Juan Bustos, "Engineering Ni catalysts for growing high quality, mechanically elastic many-layer graphene", June 2022 – August 2022
61. Austin Jeong , “Multilayer Graphene Growth on Thin Nickel Foils” January 2022 – May 2022.
60. Francis Caruso, “Integration of Dynamic Material Properties into Part-Scale Selective Laser Sintering Heat Transfer Model”, January 2022 – May 2022.
59. Shoshannah Isom, “Functionalization of Graphene”, January 2022 – May 2022.
58. Yohannes Bekele, “Increasing the Purity of Graphene using Different Molecular Weights of PMMA”, September 2021 – May 2022
57. Darren Au, “Machine Learning and Neural Networks for Image Processing” University of Texas at Austin; September 2020 – December 2020
56. Cesar Ayalam, “Machine Learning and Neural Networks for Image Processing” University of Texas at Austin; September 2020 – December 2020
55. Mateo Valdez, “Machine Learning and Neural Networks for Image Processing” University of Texas at Austin; September 2020 – December 2020
54. Rushil Patange, “Machine Learning and Neural Networks for Image Processing” University of Texas at Austin; September 2020 – December 2020
53. Ava Lindquist-Sher, “Development of a Software Architecture for Calibration and Analysis of Polariscope Image Data for Real-Time Measurement of Localized Strain in Thin Webs for R2R Nanometeology”, UT Austin; June 2021-August 2021
52. Jermy Boyle, “Tensile Strength Testing of Multilayer Graphene” University of Texas at Austin; September 2020 – December 2020
51. Pranay Srivastav, “Tensile Strength Testing of Multilayer Graphene” University of Texas at Austin; September 2020 – December 2020
50. Sucharita Banerjee, “Tensile Strength Testing of Multilayer Graphene” University of Texas at Austin; September 2020 – December 2020
49. Chieh-An Chen, “Tensile Strength Testing of Multilayer Graphene” University of Texas at Austin; September 2020 – December 2020
48. Nadia Hannon, “Carbon Sequestration Grand Challenge” University of Texas at Austin; May 2020 – August 2020
47. Ashley Baringer, “Carbon Sequestration Grand Challenge” University of Texas at Austin; May 2020 – August 2020
46. Nadia Hannon, Ashley Baringer, Claire Welton, “Carbon Sequestration Grand Challenge” University of Texas at Austin; May 2020 – August 2020
45. Gabriel Pohlman, “Carbon Sequestration Grand Challenge” University of Texas at Austin; May 2020 – August 2020
44. Nick Martinez – “Assembly of MEMS-based Metamaterial Structures”, UT Austin; January 2020 – June 2020
43. Sonia Lopez - “Testing and Measurement of MEMS Thermal Actuators”, UT Austin; January 2020 – June 2020
42. Robert Pavlovic - “In-situ Measurement of Micro-scale Stresses in Flexible Webs for Roll-to-Roll Manufacturing”, UT Austin; November 2019 – May 2019
41. Dalton Kaiser – “Design of a fixture for mounting IR heater”, UT Austin; November 2019 – May 2019
40. Alison Stutzman – “Modeling and Simulation of Nanoparticle Sintering”, UT Austin; January 2019 – May 2019
39. Reymundo Elvira – “Removing the Tensile Layer for in Exfoliated Thin Film Silicon” UT Austin; November 2019 – May 2019
38. Samuel Lee – “Finding the Appropriate Etch Barrier for Tensile Layer for in Exfoliated Thin Film Silicon”, UT Austin; January 2019 – May 2019
37. Allison Li – “Nanoparticle Layer Drying using an Infrared Heat Lamp,” University of Texas at Austin; May 2019 – August 2019
36. Gehan Jayatilaka, “Tunable Stiffness MEMS Meta-Materials Piezo Sensor Design,” University of Texas at Austin; May 2019 – December 2019
35. Ahsen Siddiqui, “Drying Profile Optimization on Spin-coated wafers with Silver Nanoparticle Inks,” University of Texas at Austin; January 2019 – May 2019
34. Sameer Walia, “Design of a z-axis Decoupling Compliant Mechanism for the Microscale SLS Machine,” University of Texas at Austin; January 2019 – May 2019
33. Daniel Liao, “Multilayer Slot Die Coating Simulation for Understanding Interlayer Characteristics in Nanoparticle Inks,” University of Texas at Austin; March 2019 – December 2019
32. Barbara Groh, "Design of an In-line Polariscope for Measurement of Dynamic Web Stresses in Roll-to-Roll Nanofabrication," University of Texas at Austin; May 2019 – August 2019
31. Mahdi Koubaa, "Design of a Flexure-based Voice Coil Alignment Mechanism for Nanopositioning Stages," University of Texas at Austin; September 2018 – May 2018
30. Gary Lei, “Optimizing the Simulation Analysis Box,” University of Texas at Austin; September 2018 – May 2019
29. Daniel Guzman, “Acetone Concentration Modeling for Precision Gas Sensor Test Rig,” University of Texas at Austin; September 2018 – May 2019
28. Wyatt Eckstrom, “Graphene Functionalization for Applications in Gas Sensing,” University of Texas at Austin; September 2018 – May 2020
27. David Sullivan, “Functional and User Friendly Breath Analysis Tool Design”, University of Texas at Austin; September 2018 – May 2019
26. Daniel Hernandez, “Acetone Gas Sensor Testing and Calibration”, University of Texas at Austin; September 2018 – May 2019
25. Zulema Jurado, “Project: Design Wafer Holder for Nickle Plating Bath,” University of Texas at Austin; June 2018 – August 2018
24. James Garcia, “Mounting Bracket Fabrication for a Roll-to-Roll Nanometrology System”, University of Texas at Austin; January 2018 – May 2022
23. George Zhou, “Data analysis: Created MATLAB Algorithm to Sort Through the Results of a Simulation and Present the Results in a Logical Manner”, University of Texas at Austin; January 2018 – May 2018
22. Danny Guo, “Initial Characterization of Silver Nanoparticle Inks”, University of Texas at Austin; January 2018 – May 2018
21. Michael Bettati, “Roller fabrication for a Roll-to-Roll Manufacturing System”, University of Texas at Austin; September 2017 – May 2018
20. Reid Goins, “Design and Fabrication of Mounting Brackets for a Two-Axis Flexure System”, University of Texas at Austin; June 2017 - August 2017
19. Williams Davenport, “Characterization of Exfoliated Silicon Wafers”, University of Texas at Austin; June 2017 - August 2017
18. Chukwubuikem Ume-Ugwa, “Data Visualization for Microscale SLS simulations”, University of Texas at Austin; June 2017 - August 2017
17. Luisa Espinosa “Design of a Stage Elevator for a Tip-based Nanometrology System”, University of Texas at Austin; June 2017 - August 2017
16. Alex Bohannon, “Fabrication of a Roll-to-Roll Tip-Based Nanometrology System,” University of Texas at Austin; April 2017 – May 2018
15. Cynthia Wu, “Electronic Circuit Design for Roll-to-Roll Tip-Based Nanometrology,” University of Texas at Austin; January 2017 – May 2017
14. Daniel Penley, “Mechatronics for Roll-to-Roll Tip-Based Nanometrology,” University of Texas at Austin; January 2017 – Present
13. James Butcher, “Metrology for Silicon Exfoliation,” University of Texas at Austin; January 2017 – May 2017
12. Godson Inikori, “Design of a Robotic Wafer Handling System,” University of Texas at Austin; September 2016 – May 2017
11. John Marshall, “Growth of Graphene on Platinum Thin Films.” University of Texas at Austin; September 2016 – May 2017
10. Jeff Hou, “Copper Nanoparticle Sintering using Ultrafast Lasers.” University of Texas at Austin; September 2016 – May 2017
9. William Jou, “Measurement of the Optical Properties of Copper Nanoparticles,” University of Texas at Austin; Summer 2016.
8. Phillip Wang, “Modeling of thermal Flows in MEMS Systems”; University of Texas at Austin; Summer 2016.
7. David Cayll, “Transfer of Graphene Grown on Thin Films” as part of NASCENT summer REU program; Summer 2016.
6. Amey Joshi, “Mechanical Modeling of Graphene-based NEMS Resonators,” University of Texas at Austin; Summer 2016.
5. Nan Hong, “Design of an Electronics Setup for Testing Graphene-based NEMS Resonators,” University of Texas at Austin; Summer 2016.
4. Jessica Sun, “Design and Fabrication of Polysilicon Piezoresistors,” as part of NASCENT summer REU program; Summer 2014
3. Cody Daniel, “Fabrication of Non-photolithographic MEMS Devices,” as part of the Undergraduate Research Opportunities Program at MIT; Summer 2010.
2. Lina Garcia, “Design of Non-photolithographic MEMS Devices,” as part of the Undergraduate Research Opportunities Program at MIT; Spring 2010.
1. Ming Leong, “Design and Fabrication of a Measurement Setup to Determine Error Motions of the Carriage in a Desktop Lathe,” as part of the Undergraduate Research Opportunities Program at MIT; Spring 2008